Claw - Instructions
Here To Buy Online
Claw™ by QuickJim™ is a curved version of the famous
The curvature of The Claw gives the user a significant reach advantage
to manipulate linkage rods below and behind the window, internal door structures
and the lock body. It’s ridged yet bendable properties allow it to
conform to different shapes and angles. The Claw can move horizontal and
vertical linkage rods to unlock many cars and trucks. It can lift the latch
on a mini-vans rear-wing window or slip through a cozy window on a semi-truck
to hit the unlock button.
The Claw has concave tips for pushing and pinch notches for grabbing.
Select the Claw that is most likely to reach your cars linkage rods. As
a guideline, the smaller QJ-CLAW-14 is for compact cars; The QJ-CLAW-16
is for mid-size cars and the QJ-CLAW-18 is for SUV’s and trucks.
|Slide the red rubber handle off to expose the pinch notches. Install
handle at other end.
||DRIVERS SIDE DOOR: Firmly hold The Claw and twist the
ends in opposite directions about 40 degrees. The inward twist allows
the Claw to angle inward.
|Insert a wedge between the window and weather strip to create a gap
for the tip of the Claw
||Slide down till you hook the linkage rod. Move forward (or back ward)
to unlock. Twist or bend the Claw as needed.
|Close-up view (from inside the truck) of The Claw pinching and moving
the linkage rod forward. Notice the Claw is working behind internal
door parts. This is the reach advantage the CLaw has over straigt slim
The greatest challenge to using The Claw is knowing where the exposed
linkage rods are. A bright light or borescope below the window can be very
helpful in locating them. Like all linkage tools, use caution as not to
exert to much perpendicular force on the linkage rod and disconnected a
linkage joint. Hope and poke is not a good strategy. The more you know
about the location of linkage rods, the more effective The Claw will become.
Other LockSmith Applications
To say the Claw is just a car lockout tool would be a gross under estimate
of its true potential and applications. In addition to unlocking cars and
trucks, The Claw can be deployed in so many other ways.
||The Claw can slide between a pair of non-mullion commercial doors
and retract a paddle handle (photo 10), exit bar and lever handle.
It can even manipulate the thumb turn of an Adams Rite deadbolt lock.
||The Claw can be used to unlock some models of file cabinets desks
or drawers. Can slip between a pair of sliding glass doors (old style
non-interlocking) and lift up a bar or manipulate the lock on a window.
||It can retract a spring latch behind a (photo 9) latch guard and
even hook the rope release on an overhead garage door. It can grab
and release a surface mounted door chain or flip bar and so much more!
Car Unlock Tools |
8095 Beckett Center Drive, West Chester, Ohio 45069 | eMail
NOTE: QuickJim Lockout
tools are not sold to the general public. To purchase QuickJim products,
you must be a member of law enforcement,
a fireman, EMS, locksmith, tow truck operator, campus security, car dealership,
auto repair shop or distributor of the same.
Several patents pending. Company service marks
and trademarks include QuickJim™, Curls in – Unlocks – Curls
out™, Spiral Locksmith Tool™, Spiral Car Tool™,
Spiral Unlock Tool™, Spiral Open Tool™
KwikJim™, KwickJim™ ,
SpiralJim™ , Quick-Jim™, Kwik-Jim™ , Carsnake™, CurlyJim™, Tools
That Get You In™, The Claw™, FlexJim™ . ©
all rights reserved.
site created by Bold Statement Web Design